Looking for a PoE switch connecting your IP camera?
This switch has 8 ports in total and 4 of these ports can be used as PoE.
Data transmission is quick: 10/100Mbps. it is also not difficult to connect, plug in and it works.
To make use of Ethernet Cat5/Cat5e/Cat6 cables can be used.
This switch is fully compatible to devices that comply with the IEEE 802 .3af PoE standard.
It's easy to add devices that have Wireless Access points (APS).
Thus, it is possible to IP cameras, VOIP phones, printers, and Network Attached Storage (NAS) to connect directly on one of the gates.
It is not necessary to have an additional socket in the vicinity.
There is no configuration required and installation is quick and easy.
Support for Auto-MDI/MDI-X on all ports and eliminates the need for cross-over connection for another switch or HUB.
The speed is intelligently adjusted so that the device looks for the most optimal performance.
PoE is very easy and will save up to 50% time and cost because there is no separate electrical wiring to be installed.
The switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and runs in both half and full duplex mode using two pairs of category 5 or 5e cable.
All ports are Auto-MDI type. The switch can automatically convert to MDII or MDI-X type, so you can use the RJ-45 cable regardless of whether it is a standard or crossover cable.
- 8 x 10/100Mbps Auto-negotiation fast Ethernet RJ-45 ports with 4-Port PoE function (port 1 ~ 4 port)
- Compatible with IEEE 802 .3af specification
- Supports PoE PoE ports for all consumption to 56W
- Supports PoE IEEE 802 .3af compatible powered device (PD)
- Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
- Full/half-duplex transfer mode for each port.
- Send and receive
- 64KBytes packet buffer
|Standard||IEEE 802.3 10BASE-T Ethernet.
IEEE 802.3u 100BASE-TX Fast Ethernet.
IEEE 802.3x Full Duplex Flow Control.
IEEE 802.3af Power over Ethernet.
|Data Transfer Rate||Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex).
Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex).
|Network Cables||10BASE-T: 2-pair UTP Cat 3, 4, 5 up to 100 meters.
100BASE-Tx: 2-pair UTP Cat 5, 5e up to 100 meters.
|Number of Ports||
8 x 10/100Mbps auto-MDIX RJ-45 ports with 4/8 PoE enabled ports.
|PoE power on RJ-45||Power +: ping 3 & ping 6 ; Power –: ping 1 & ping 2.|
|AC to DC power adaptor||Input: 110V ~ 240VAC, 50Hz ~ 60Hz.
Output: 48VDC/1.25A (4 PoE port )
|Power Consumption||6.4 watts ( max with no PD device connected).
56 watts ( 4 PoE ports full load ).
|Temperature||Operation: 0℃ ~ 40 ℃ or 32℉ ~ 104 ℉.
Storage Temperature: -10℃ ~ 70 ℃ or 14℉ ~ 158 ℉.
|Humidity||Relative Humidity: 5% - 95%.|
|Dimensions||190mm W x 140mm D x 43mm H|
|EMI||FCC Class B, CE Mark Class B.|
|Safety||110VAC to 240VAC power adaptor UL listed.|
|RAM buffer||64K bytes per device.|
|Filtering Address Table||1K entries per device.|
Packet Filtering/ Forwarding Rate
10Mbps Ethernet: 14,880/pps
10Mbps Ethernet: 148,800/pps
|MAC address Learning||Automatic update.|
|Transmission Method||Store – and – forwarder.|
|PoE Ports||4 Ports|