A switch to connect your IP cameras?
You can do this with the PoE switch.
This switch features 24 ports to connect.
Very easy to use, no installation needed.
There is no configuration required and installation is quick and easy.
Support for Auto-MDI/MDI-X on all ports and eliminates the need for cross-over connection for another switch or HUB.
The speed is intelligently adjusted so that the device is always looking for the most optimal performance.
The 5-port 10/100 Ethernet Switch PoE supports five 10/100Mbps Ethernet ports.
Port 1 to 4 of the port are PoE enabled ports.
Each port contains 10/100Mbps support via UTP CAT5/5e cables.
The four PoE ports are automatically activated when a compatible device is identified.
The 5-port 10/100 Ethernet PoE Switch will supply power via the Ethernet port on the connected PoE device (PD)
The switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and runs in both half and full duplex mode using two pairs of category 5 or 5e cable.
All ports are Auto-MDI type. The switch can automatically convert to MDII or MDI-X type, so you can use the RJ-45 cable regardless of whether it is a standard or crossover cable.
PoE supported multiple types of devices such as wireless LAN access points, VOIP telephone and IP security cameras.
PoE is very easy and will save up to 50% time and cost because there is no separate electrical wiring that must be installed.
- 24 x 10/100Mbps Auto-negotiation fast Ethernet RJ-45 ports with 24 ports PoE Act (port 1 ~ 24 port).
- Complies with IEEE 802 .3af (PoE 24-Port 10/100 M Ethernet Switch).
- Supports PoE power to 340W for all PoE ports.
- Supports PoE IEEE 802 .3af compatible powered device (PD)
- Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
- Full and half duplex transfer mode for each port.
- Send and receive
- 64KBytes packet buffer
|Standard||IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3x Full Duplex Flow Control
IEEE 802.3af Power over Ethernet
|Data Transfer Rate||Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex)
|Network Cables||10BASE-T: 2-pair UTP Cat 3, 4, 5 up to 100 meters.
100BASE-Tx: 2-pair UTP Cat 5, 5e up to 100 meters.
|Number of Ports||24 x 10/100Mbps auto-MDIX RJ-45 ports with 24 PoE enabled ports.|
|PoE power on RJ-45||Power +: ping 3 & ping 6 : Power –” ping 1 & ping 2|
|AC to DC power supply||Input: 110V ~ 240VAC, 50Hz ~ 60Hz. Output: 48VDC / 7.3A|
|Power Consumption||8.0 watts ( max with no PD device connected)
340 watts (23 PoE ports 15.4W/port)
|Temperature||Operation: 0℃ ~ 40 ℃ or 32℉ ~ 104 ℉
Storage Temperature: -10℃ ~ 70 ℃ or 14℉ ~ 158 ℉
|Humidity||Relative Humidity: 5% - 95%|
|Dimensions||430mm W x 256mm D x 66.4mm H|
|EMI||FCC Class B, CE Mark Class B|
|Safety||110VAC to 240VAC power supply UL listed.|
|RAM buffer||64K bytes per device|
|Filtering Address Table||1K entries per device|
|Packet Filtering Forwarding Rate||10Mbps Ethernet: 14,880/pps
10Mbps Ethernet: 148,800/pps
|MAC address Learning||Automatic update|
|Transmission Method||Store – and – Forward|
|PoE Ports||24 Ports|